Torque Meter

Schmidt Control Instruments

A Torque meter is a force gauge for determining the torque. Torque gauges with separate sensors are suitable for torque measurements of screws, components, switches, drive shafts, etc., while desktop torque meters are used to check the opening and closing forces of screw caps on bottles, cans, cosmetics, etc.

Combining a desktop-torque meter with a motorized test stand gives you a torque testing machine for maximum accuracy, since it does not affect the measuring result by the operator. Due to the high measuring frequency of 2000 measurements / s peak values can be recorded exactly.

Every torque meter has an easy-to-read OLED display, with various selectable units of measurement and menu languages. The internal memory of a torque tester offers space for approx. 1000 measurements. All torque gauges are equipped with a USB and RS-232 interface, with which data can be transferred to a PC and evaluated.

Torque Meter
Torque Meter HTGS and HTGA

Torque Meter HTGS and HTGA

  • Hand-held device with separate sensor
  • to measure the torque of screws, components etc.

Measuring ranges:

  • 0.5, 2, 5, and 10 Nm
  • Mains and battery operation
  • Output signal and memory
Torque Meter DTXS and DTXA

Torque Meter DTXS and DTXA

  • Desktop-torque meter
  • For measuring the cap torque of bottles, glass jars etc.

Measuring ranges:

  • 0.5, 2, 5, and 10 Nm
  • Mains or battery operation
  • Output signal and memory
Torque Stand MTS

Torque Stand MTS

  • Desktop-torque meter
  • For measuring the cap torque of bottles, glass jars etc.

Measuring ranges:

  • 0.5, 2, 5 or 10 Nm
  • Single tests
  • Endurance tests
  • Output signal and memory

SCHMIDT Torque Meter HTGS and HTGA

Measuring ranges 50.00 Ncm/2.000 Nm/5.000 Nm/10.00 Nm resolution 0.01 Ncm/0.001 Nm/0.01 Nm.

Hand-held torque meter with separate sensor for measuring the torque of screws, components, screw and plug connectors, drive shafts etc.

Mains and battery operation with memory and output signal.

Torque meter with digital output signal for data processing with a PC.

Special Features

  • 2 selectable modes:
    – Real Time: to display torque transition
    – Peak Mode: to capture the peak torque achieved during a test

  • Display of opening or closing torque (clockwise and counterclockwise torque)
  • Torque meter with high internal sampling rate of 2000 times/sec
  • Display update time 10 times/sec
  • Easy to read Display (OLED)
  • Selectable units: Nm, Ncm, kgfm, kgfcm, Lbf.in or ozf.in
  • Multi language set up menu: English, German, Spanish, French, Italian, Chinese, Japanese, Korean
  • Programmable high/low setpoints for go/no-go testing with color-coded indicators (orange, green, red) in the LED display and relay outputs
  • Storage of 1000 values for recall:
    • on the display
    • for data transfer to PC
    • for printing with report
  • 4 output signals: USB, RS-232, analog and Mitutoyo Digimatic
  • 6 different sensor attachments are available
  • The torque sensors of torque meter HTGS-10N and HTGA-10N includes an additional supporting handle for better operation

Special features of model HTGA in comparison to standard unit HTGS:

 

  • Readings can be transferred from the internal memory to an USB flash drive or directly saved on it (sampling rate 100 times/sec)
  • 2 high/low output values can be set; If the reading reaches one of the output values, data will be sent to external devices (e.g. PC, printer) for data recording
  • Indication of two peak values per measurement.

Standard Features

  • Inclusive 30 days trial version of Software »Force Recorder Professional«
  • Torque measuring unit for fast, accurate measuring
  • High repeatability
  • Easy to use
  • Manufacturer`s certificate with measured values is included.

Available Models

Model Model Measuring Range
Resolution
HTGS-0.5N HTGA-0.5N 0 – 50.00 Ncm 0.01 Ncm
HTGS-2N HTGA-2N 0 – 2.000 Nm (200 Ncm) 0.001 Nm (0.1 Ncm)
HTGS-5N HTGA-5N 0 – 5.000 Nm (500 Ncm) 0.001 Nm (0.1 Ncm)
HTGS-10N HTGA-10N 0 – 10.00 Nm (1000 Ncm) 0.01 Nm (1 Ncm)
Accuracy: ±0.5 % full scale ±1 digit
Measuring frequency: 2000 times/s
Selectable units: Nm, Ncm, kgfm, kgfcm, Lbf.in, and ozf.in
Display: OLED, 4 digit, 14 mm high
Overload capacity: Approx. 200 % full scale, flashing display beyond 110 % full scale
Display update: 10 times/sec.
Memory: Internal memory for max. 1000 values (clockwise or counter clockwise torque and peak values)
Setpoints: MIN (-NG), MAX (+NG) programmable, with output signal
Output signal: USB
RS-232 (8, 1, N, 19200)
analog ±2 V DC
Mitutoyo Digimatic
Open Collector-Comperator 3 x (+NG, Ok, -NG)
overload signal
Temperature range: 0 – 40 °C
Air humidity: 80 % RH, max.
Power supply: Rechargeable NiMH battery pack (approx. 8 hours continuous use) and/or 100 – 240 V AC adapter with two adapters(EU/USA)
Dimensions (approx.): Display unit: 187 x 75 x 34 mm (LxWxH)
Sensor: 183 x 39 mm (LxØ)
Weight: (approx.): Display unit: 490 g / sensor: 530 g (without pin chuck)
complete set 2000 g
Additional functions of HTGA in comparison to standard torque meter HTGS:
Torque-angle-measurement: In combination with a test stand with linear scale torque-angle-measurements are possible
Memory: Readings can be transferred from the internal memory to an USB flash drive or directly saved on it (sampling rate 100 times/sec)
High low output: 2 high/low output values can be set; If the reading reaches one of the output values, data will be sent to external devices
(e.g. PC, printer) for data recording
Extended peak mode: Indication of two peak values per measurement

Specifications subject to change without notice

Scope of delivery torque meter HTGS

  • Torque meter with 1 torque sensor and without sensor attachment,
  • Handle (only HTGS/-A-10N),
  • AC Adapter,
  • carrying case,
  • manufacturer`s inspection certificate,
  • USB cable 1.5 m,
  • USB adapter (only HTGA),
  • CD-ROM with Driver,
  • simple Software for communication and data logging »ZT-Logger« and operating instructions.

SCHMIDT Torque Meter DTXS and DTXA

Measuring ranges 50.00 Ncm/2.000 Nm/5.000 Nm/10.00 Nm resolution 0.01 Ncm/0.001 Nm/0.01 Nm

Desktop-torque meter with memory and output signal for checking the opening and close torque of screw caps of bottles, glass jars, cosmetics etc. For applications in beverage, cosmetic and pharmaceutical industry etc.

Torque meter with digital output signal for data processing with a PC

Special Features

  • Displaying the opening or closing torque (clockwise and counterclockwise torque)
  • 2 selectable modes:
    • Real Time: to display load transients
    • Peak: to capture the peak torque achieved during a test
  • Table for containers with Ø from 20 to 160 mm (small table for diameters from Ø 7 up to 50 mm is available) – standard unit
  • Programmable high/low setpoints for go/no-go testing with color-coded indicators (orange, green, red) in the LED display and relay outputs
  • Torque meter with high internal sampling rate of 2000 times/sec
  • Display update time 10 times/sec
  • Torque meter with easy to read display (OLED)
  • Selectable units: Nm, kgfm, Lbf.in or Ncm, kgfcm, ozf.in
  • Storage of 1000 values for recall:
    • on the display
    • for data transfer to a PC
    • for printing with report
  • 4 output signals: USB, RS-232, analog, and Mitutoyo Digimatic

Special features of model DTXA in comparison to standard unit DTXS

  • Readings can be transferred from the internal memory to an USB flash drive or directly saved on it (sampling rate 100 times/sec).
  • 2 high/low output values can be set; If the reading reaches one of the output values, data will be sent to external devices (e.g. PC, printer) for data recording
  • Indication of two peak values per measurement, e. g. closure with rated break point.

Standard Features

  • Torque meter for fast, accurate measuring
  • High repeatability
  • Easy to use
  • Inclusive 30 days trial version of Software »Force Recorder Professional«
  • Manufacturer`s certificate with measured values is included.

Available Models (Standard Unit)

Model Model Measuring Range
Resolution
DTXS-0.5N* DTXA-0.5N* 0 – 50.00 Ncm 0.01 Ncm
DTXS-2N** DTXA-2N** 0 – 2.000 Nm (200 Ncm) 0.001 Nm (0.1 Ncm)
DTXS-5N** DTXA-5N** 0 – 5.000 Nm (500 Ncm) 0.001 Nm (0.1 Ncm)
DTXS-10N** DTXA-10N** 0 – 10.00 Nm (1000 Ncm) 0.01 Nm (1 Ncm)

* includes table DT-STL
** includes table DT-TB

Available Models (Self Configurated)

Model Model Description
DTXS-0.5N-Z DTXA-0.5N-Z without table
DTXS-2N-Z DTXA-2N-Z without table
DTXS-5N-Z DTXA-5N-Z without table
DTXS-10N-Z DTXA-10N-Z without table
Accuracy: ±0.5 % full scale ±1 digit
Measuring frequency: 2000 times/sec.
Selectable units: Nm, Ncm, kgfm, kgfcm, Lbf.in and ozf.in
Display: OLED, 4 digit, 14 mm high
Overload capacity: Approx. 200 % full scale,
flashing display beyond 110 % full scale
Display update: 10 times/sec
Memory: Internal memory for max. 1000 values (clockwise or counter clockwise torque and peak values)
Setpoints: MIN (-NG), MAX (+NG) programmable, with output signal
Output signal: USB
RS-232 (8, 1, N, 19200)
analog ±2 V DC
Mitutoyo Digimatic
Open Collector 4x (+NG, Ok, -NG, OVL), max. 30 V DC, 10 mA
overload signal
Temperature range: 0 – 40 °C
Air humidity: 80 % RH, max.
Power supply: Rechargeable NiMH battery pack (approx. 8 hours continuous use) and/or 100 – 240 V AC adapter with two adapters (EU/USA)
Dimensions (approx.): 305 x 233 x 127 mm (LxWxH)
Weight: net (gross.): Approx. 4900 g (approx. 5900 g)
Additional functions DTXA in comparison to standard torque meter DTXS:
Torque-angle-measurement: In combination with a test stand with linear scale torque-angle-measurements are possible e.g. MTS-10N-RA
Memory: Readings can be transferred from the internal memory to an USB flash drive or directly saved on it (sampling rate 100 times/sec)
High low output: 2 high/low output values can be set; If the reading reaches one of the output values, data will be sent to external devices
(e.g. PC, printer) for data recording
Extended peak mode: Indication of two peak values per measurement

Specifications subject to change without notice.

  • Torque meter,
  • 1 table DT-TB,
  • 1 set spring pins 25 mm long,
  • AC adapter,
  • manufacturer`s inspection certificate,
  • USB cable 1.5 m,
  • USB adapter (only DTXA),
  • CD-ROM with driver,
  • simple software for communication and data logging »ZT-Logger« operating instructions.

SCHMIDT Torque Stand MTS

Measuring ranges 0 – 50.00 Ncm, 0 – 2.000 Nm, 5.000 Nm or 10.00 Nm resolution depending on the range 0.01 Ncm, 0.001 Nm or 0.01 Nm

Motorized test stand for determining and testing the opening and closing forces of screw caps, used for bottles, cans, cosmetic products etc. Further application areas are testing torque switches, plugs, lenses etc.
The most important sectors of industry are the pharmaceutical, cosmetics, beverage and electronic industry, etc.

Torque stand assures constant, identical measuring conditions.

Special Features

Special Features Torque Stand
  • The motorized torque stand MTS can be configurated according the customers demand. The torque stand exists out of a test stand depending the sample height, a torque meter with different ranges and features as well as a upper chuck and lower table.
  • The torque will be measured without influence by the operator. The results are more accurate and significant as measured with a manual device.
  • 3 operation modes:
    • Normal: Revolution occurs in the selected direction, until the stop-switch will be pressed.
    • +NG Stop: Revolution occurs in one direction, until the adjusted value is reached.
    • Endurance Test: Repeats the operation in two directions (open – close), within the adjusted limits (MTS series). The number of repeats are shown in the display. The opening and closing angle, as well as the number of repeats can be adjusted with torque stand MTS-RA series.
  • The following information are shown in the display:
    • Rotational speed e. g. 51.5 °/sec
    • Status of the instrument
    • Operation mode
    • Counter for endurance test
  • Max. size of samples:
    • upper clamping chuck Ø 20 – 90 mm or Ø 7 – 50 mm
    • lower clamping table Ø 20 – 160 mm or Ø 7 – 50 mm
    • Max. available sample height 140, 240 mm or 340 mm
  • The rotation speed can continuously be adjusted to 3 – 90 degree/sec. The value will be displayed.
Special Features DTXS and DTXA
  • 2 Display Modes:
    • Real Time: displays the actual torque
    • Peak Force: to measure and save the peak torque
  • Display the opening or closing torque (clockwise and counter clockwise torque)
  • 3 selectable units: Nm, kgfm, Lbf.in or Ncm, kgfcm, ozf.in
  • Programmable high/low setpoints for go/no-go testing with color-coded indicators (orange, green, red) in the LED display
  • Torque meter with high internal sampling rate of 2000 times/sec to capture peak values
  • Storage of 1000 values for recall:
    • On the display
    • For data transfer to a PC
    • For printing with report
  • 4 output signals: USB, RS-232, analog, and Mitutoyo Digimatic
  • Display update time 10 times/sec
  • Easy to read display (OLED) for Real Time or Peak value including units. Depending to the series additional information are displayed as e. g. memory, number of good tests, limits, 1st and 2nd peak values etc.

Special features of model DTXA in comparison to the standard model DTXS:

  • Indication of 1st and 2nd peak value per measurement, e. g. closure with predetermined break point
  • Readings can be transferred from the internal memory to an USB flash drive or directly saved on it (sampling rate 100 times/sec)
  • 2 comparator values can be set; If the reading reaches one of the output values, data will be sent to external devices (e.g. PC, printer) for data recording.

Special features of model MTS-RA in combination with the torque meter DTXA in comparison with the standard model MTS with the torque meter DTXS

Torque-angle measurements are possible. The software “Force Recorder Professional” is additionally required.

Standard Features

  • Torque stand MTS for fast, accurate measuring
  • High repeatability
  • Easy to use
  • Inclusive 30 days trial version of Software »Force Recorder Professional«
  • Manufacturer`s certificate with measured values is included.

Available Models (Torque Stands)

Model Max. Sample Height
Description
MTS-10N 140 mm
MTS-10N-L 240 mm
MTS-10N-2L 340 mm
MTS-10N-RA 140 mm with rotary encoder
MTS-10N-L-RA 240 mm with rotary encoder
MTS-10N-2L-RA 340 mm with rotary encoder

Available Models (Standard Model)

Model Model Measruing Range
Resolution
DTXS-0.5N DTXA-0.5N 0 – 50.00 Ncm 0.01 Ncm
DTXS-2N DTXA-2N 0 – 2.000 Nm (200 Ncm) 0.001 Nm (0.1 Ncm)
DTXS-5N DTXA-5N 0 – 5.000 Nm (500 Ncm) 0.001 Nm (0.1 Ncm)
DTXS-10N DTXA-10N 0 – 10.00 Nm (1000 Ncm) 0.01 Nm (1 Ncm)

*inclusive table DT-TB

Available Models (Self Configurated)

Model Model Description
DTXS-0.5N-Z DTXA-0.5N-Z without table
DTXS-2N-Z DTXA-2N-Z without table
DTXS-5N-Z DTXA-5N-Z without table
DTXS-10N-Z DTXA-10N-Z without table
Torque Stand
Sample Height: Max. 140, 240 or 340 mm
Speed: 3 – 90 °/s adjustable
Temperature range: 0 – 40 °C
Air humidity: 80 % RH, max.
Power supply: 100 – 240 V AC, 50/60 Hz, max. 3 A
Housing dimensions: See dimensions
Weight: 14 kg net without accessories
Torque Meter
Accuracy: ±0.5 % full scale ±1 digit
Measuring frequency: 2000 times/s
Selectable units: Nm, kgfm, Lb.in or Ncm, kgfcm, Lb.in
Display: OLED, 4 digit, 14 mm high
Overload protection: Approx. 200 % full scale, flashing display beyond 110 % full scale
Display update: 10 times/s
Memory: Internal memory for max. 1000 values, (clockwise or counter clockwise and peak values)
Setpoints: MIN (-NG), MAX (+NG) adjustable with output signal
Output signal: USB
RS-232 (8, 1, N, 19200)
analog ±2 V DC
Mitutoyo Digimatic
Open collector 4x (+NG, Ok, -NG, OVL), max. 30 V DC, 10 mA
overload signal
Temperature range: 0 – 40 °C
Air humidity: 80 % RH max.
Power supply: Rechargeable NiMH battery pack (approx. 8 hours continuous use) and/or AC adapter 100 – 240 V AC with two adapters (EU/USA)
Housing dimensions: 305 x 233 x 127 mm (LxWxH)
Weight, net (gross): Approx. 4900 g (Approx. 5900 g)
Additional functions model DTXA in comparison to model DTXS:
Memory: Readings can be transferred from the internal memory to an USB flash drive or directly saved on it (sampling rate 100 times/s)
High low output: 2 high/low output values can be set. If the reading reaches one of the output values, data will be sent to external devices (e. g. PC, printer) for data recording
Extended peak mode: Indication of two peak values per measurement
Additional functions model MTS-RA in combination with DTXA:
Torque-displacement-measurement: The Software Force Recorder Professional is required

Specifications subject to change without notice

  • Torque stand MTS,
  • torque meter,
  • upper and lower clamping device,
  • AC adapter,
  • manufacturer`s inspection certificate,
  • USB cable 1.5 m,
  • CD-ROM with driver,
  • simple software for communication and data logging »ZT-Logger«, connecting cable and operation instructions in English.

Feel free to discuss your purchasing plan with us

Pin It on Pinterest

Share This